275Spezialnähmaschinemit DirektantriebBetriebsanleitungInstruction manualPostfach 17 03 51, D-33703 Bielefeld • Potsdamer Straße 190, D-33719 Bielefel
61231011456987
1. Scope of DeliveryWhat items are supplied depends on your order.Before setting-up please check that all the required components are present.Equipmen
812345671514131211109814
3. Assembling the stand3.1 Assembling the stand parts–Assemble the frame components as shown in the illustration.–Fit the four enclosed feet 6 to the
1012345671514131211109814
3.2.2 Machines with an edge cutter(classes 275-740642 and 275-742642)–Fit the top support 15 into the hole in the table plate.–Fit the rubber rests 14
1221 22 2317181920
3.2.3 Machines with an edge cutter and fullness control(class 275-742642)(for items 1-16 see the preceding pages)–Attach items 1-16 as described in th
3.3 Adjusting the working heightThe working height can be adjusted between 750 and 950 mm (measured to the upperedge of the table top).–Undo screws 1
4. Assembling the machine head4.1 Fitting the machine headCAUTION:Remove the front and centre support screws before tiltinginto the working position.–
Alle Rechte vorbehalten.Eigentum der Dürkopp Adler AG und urheberrechtlich geschützt. J ede, auchauszugsweise Wiederverwendung dieser Inhalte ist ohne
5. Sewing drive5.1 Items suppliedDC1500/DA220C positioning actuator–DC1500 motor–DA220C control–EB301 A set-point generator–pedal linkage–attachment i
5.3.2 Subclass 275-742642With this subclass a large number of assemblies are fitted under the table top, so it isessential to comply with the dimensio
181223
6. Electrical connectionCAUTION:All work on the electrical equipment of this special sewingmachine may only be carried out by qualified electricianswh
6.3 Fitting and connecting the sewing-light transformer (optional equipment)–Remove the mains plug.–Connect the mains cable of the sewing-light transf
6.4 Connection sockets on the DA220C control6.5 Connecting the DA220C control–Plug the set-point generator (pedal) lead into socket B80 of the control
6.6 Checking the direction of rotation of the sewing driveCAUTION:Before the special sewing machine is started it is essentialto check the direction o
6.7 Checking the positioningNeedle positions are correctly set prior to delivery, but they should still be checkedbefore starting the machine.NB:The s
7. Operating and adjusting the DC1500/DA220Cdirect-current positioning actuatorOperationThe DA220C control contains all operating components necessary
7.1 DA220C control operating and display elementsKey Function in sewing mode (main switch on)P enter / leave programming modeE starting bar tack singl
ForewordThis instruction manual is intended to help the user to becomefamiliar with the machine and take advantage of its applicationpossibilities in
LED FunctionLED1 on display for single starting bar tackLED2 on display for double starting bar tackLED1 and LED2 off starting bar tack offLED3 on dis
7.1.1.2 Calling and changing operator-level parameters directly with theDA220C control–Turn on the main switch.–The value for the maximum speed appear
7.1.3 DA220C control operator-level parameter listParameter adjustment rangepre-set valueNo. Abb. Name/Function min max 100R000 c2 starting-bar-tack s
7.1.4 Changing technician-level and manufacturer-level parameter valuesCAUTION:Great care must be taken when changing parameter values,as an incorrect
Entering the manufacturer-level code with the DA220C control–Turn off the main switch.–Press and hold down the “P”key.–Turn on the main switch: “Cod”
Setting positions 1 and 2Prerequisite:The reference position has been set (see section 7.1.5, “Setting the referenceposition”).NB:The position values
7.1.6 Setting machine-specific parameters with the DA220C control7.1.6.1 GeneralThe sewing-drive control functions are determined by the program and t
** A function module is a part of the control that handles one of the machine’s facilities,e.g. raising and lowering the transport roller. The control
7.1.8 Condition and error messagesGeneral informationDA220C V810 V820 MeaningA1 InF A1 InFo A1 The pedal is not in its zero positionwhen the sewing dr
7.2 V810 operating panel (optional equipment)7.2.1 Operating and display elements on the V810 operating panel7.2.2 key functions on the V810 operating
General safety instructionsThe non-observance of the following safety instructions can cause bodily in-juries or damages to the machine. 1. The machi
Symbol Function DisplayB needle up/down no displayor shift function in programming modepressing this key executes a needle movementthat can be program
7.2.4 Changing parameter values at operator levelThe operator-level parameters are given in the parameter list in section 7.1.3.–Turn on the main swit
7.2.6 Changing technician-level and manufacturer-level parameter values withthe V810 operating panelEntering the technician-level code–Turn off the ma
CAUTION:The changed parameter values are not saved unless acomplete seam is sewn after leaving the programminglevel, i.e. the pedal is pushed forwards
–Correct the parameter value * if necessary, either with the “+”or“-”keysorbyturning the handwheel.–Press the “P” key twice to leave the programming l
7.3 V820 operating panel (optional equipment)7.3.1 Operating and display elements on the V820 operating panel7.3.2 Key functions on the V820 operating
Key Function Display7 basic needle position = down left arrow above the key onbasic needle position = up right arrow above the key on8 residual-thread
7.3.3 Meaning of the symbols on the V820 operating panelSymbol Function DisplayC abbreviation for code symbol on when a code isdisplayed, e.g. C 1907D
7.3.4 Changing parameter values at operator levelThe operator-level parameters are given in the parameter list in section 7.1.3.–Turn on the main swit
7.3.7 Changing technician-level and manufacturer-level parameter values withthe V820 operating panelEntering the technician-level code–Turn off the ma
Contents page:Part 2: Installation instructions Cl. 275 direct drive1. Scope of delivery ... 72. General and transport pack
7.3.8 Setting positions with the V820 operating panelSetting the reference positionPrerequisite:The technician-level code has been set. See section 7.
*CAUTIONThe parameter values for positions 1E, 2E, 1A and 2A canbe found in the parameter sheet (accessory kit).NB:If position checking establishes th
7.3.11 Condition and error messages on the V820 operating panelSee section 7.1.8.7.3.12 Seam programming with the V820 operating panelA maximum of 8 p
8. Fullness control in classes 275-142342 and 275-7426428.1 Checking the basic control settingOnce the machine has been set up the basic control setti
8.1.3 Activating the next seam sequence when the thread is cutWhen the program contains fullnesses the next seam sequenceis normally activated by the
9. Pneumatic connectionCAUTION:The pneumatic units will only operate properly at a supplypressure of 8 to 10 bar.The special sewing machine’s operatin
10. LubricationSee Operating instructions, section 8.2: “Lubrication”11. Sewing testA sewing test must be carried out when setting-up is complete.–Ins
Contents page:7. Operating and adjusting the DC1500/DA220C direct-currentpositioning actuator ... 247.1 DA220C control operat
Contents page:8. Fullness control in classes 275-142342 and 275-742642 ... 498.1 Checkingthebasiccontrolsetting... 498.1.1 Adjust
Notes5GB
Comentarios a estos manuales